收藏本站
71M6545/71M6545H Data Sheet
Table 23: The TCON Register Bit Functions (SFR 0x88)
Bit
TCON[7]
TCON[6]
TCON[5]
TCON[4]
TCON[3]
TCON[2]
TCON[1]
TCON[0]
Symbol
TF1
TR1
TF0
TR0
IE1
IT1
IE0
IT0
Function
The Timer 1 overflow flag is set by hardware when Timer 1 overflows.
This flag can be cleared by software and is automatically cleared when an
interrupt is processed.
Timer 1 run control bit. If cleared, Timer 1 stops.
Timer 0 overflow flag set by hardware when Timer 0 overflows. This flag
can be cleared by software and is automatically cleared when an interrupt
is processed.
Timer 0 Run control bit. If cleared, Timer 0 stops.
Interrupt 1 edge flag is set by hardware when the falling edge on external
pin int1 is observed. Cleared when an interrupt is processed.
Interrupt 1 type control bit. Selects either the falling edge or low level on
input pin to cause an interrupt.
Interrupt 0 edge flag is set by hardware when the falling edge on external
pin int0 is observed. Cleared when an interrupt is processed.
Interrupt 0 type control bit. Selects either the falling edge or low level on
input pin to cause interrupt.
2.4.9
WD Timer (Software Watchdog Timer)
There is no internal software watchdog timer. Use the standard hardware watchdog timer instead (see
2.5.13 Hardware Watchdog Timer ).
2.4.10 Interrupts
The 80515 provides 11 interrupt sources with four priority levels. Each source has its own interrupt request
flag(s) located in a special function register ( TCON , IRCON , and SCON ). Each interrupt requested by the
corresponding flag can be individually enabled or disabled by the enable bits in IEN0 (SFR 0xA8) , IEN1
(SFR 0xB8) , and IEN2 (SFR 0x9A) . Figure 12 shows the device interrupt structure.
Referring to Figure 12, interrupt sources can originate from within the 80515 MPU core (referred to as
Internal Sources) or can originate from other parts of the 71M6545/H Metrology Processor (referred to as
External Sources). There are seven external interrupt sources, as seen in the leftmost part of Figure 12 ,
and in Table 24 and Table 25 (i.e., EX0-EX6 ).
Interrupt Overview
When an interrupt occurs, the MPU vectors to the predetermined address as shown in Table 36 . Once
the interrupt service has begun, it can be interrupted only by a higher priority interrupt. The interrupt service
is terminated by a return from instruction, RETI. When an RETI is performed, the processor returns to the
instruction that would have been next when the interrupt occurred.
When the interrupt condition occurs, the processor also indicates this by setting a flag bit. This bit is set
regardless of whether the interrupt is enabled or disabled. Each interrupt flag is sampled once per
machine cycle, then samples are polled by the hardware. If the sample indicates a pending interrupt when
the interrupt is enabled, then the interrupt request flag is set. On the next instruction cycle, the interrupt is
acknowledged by hardware forcing an LCALL to the appropriate vector address, if the following conditions
are met:
?
?
?
No interrupt of equal or higher priority is already in progress.
An instruction is currently being executed and is not completed.
The instruction in progress is not RETI or any write access to the registers IEN0 , IEN1 , IEN2 , IP0 or IP1 .
Special Function Registers for Interrupts
The following SFR registers control the interrupt functions:
?
?
40
The interrupt enable registers: IEN0, IEN1 and IEN2 (see Table 24 , Table 25 and Table 26 ).
The Timer/Counter control registers, TCON and T2CON (see Table27andTable28).
v2
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
720-10007-00300 CBL D-SUB 9PIN FMAL-25PIN FML 3M
720-10010-00025 CBL DSUB 9PIN FML-25PIN MAL .25M
720-10020-00300 CBL DSUB 9PIN FML-9PIN MALE 3M
720-10021-00300 CBL DSUB 9PIN FML-9PIN FEMAL 3M
72231-0881 8 POS T/P SHLD 4 GR ASSY
7250B PANEL KIT BOTTOM FOR R-1220 CASE
731-10061-00200 CBL DSUB HD 15FEMAL-15MALE 2.0M
73304-111 MJ HOR ESMT 8/8 H/O T&R
相关代理商/技术参数
71M6545-IGTR/F 功能描述:计量片上系统 - SoC Metrology Proc. (3P 64K Flsh .1%) RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel
71M6545T-IGT/F 制造商:Maxim Integrated Products 功能描述:METROLOGY PROCESSORS - Rail/Tube
71M6545T-IGTR/F 制造商:Maxim Integrated Products 功能描述:3-PHASE AFE, 32KB FLASH, PRES TEMP SENSOR - Tape and Reel
71M6601 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:On-Chip Temperature Sensor Enables Localized Digital Temperature On-Chip Power Monitoring
71M6601-IF 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:On-Chip Temperature Sensor Enables Localized Digital Temperature On-Chip Power Monitoring
71M6601-IL 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:On-Chip Temperature Sensor Enables Localized Digital Temperature On-Chip Power Monitoring
71M6601-IL/F 功能描述:模数转换器 - ADC Isolated Sensor IC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32
71M6601-ILF 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:On-Chip Temperature Sensor Enables Localized Digital Temperature On-Chip Power Monitoring